Delta 31 Manuál s instrukcemi

Procházejte online nebo si stáhněte Manuál s instrukcemi pro Elektrické brusky Delta 31. Delta 31 Instruction manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
INSTRUCTION MANUAL
6" Belt and 12" Disc
Abrasive Finishing Machine
(Model 31-731)
PART NO. 420-01-651-0013 - 05-28-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Abrasive Finishing Machine

INSTRUCTION MANUAL6" Belt and 12" DiscAbrasive Finishing Machine(Model 31-731)PART NO. 420-01-651-0013 - 05-28-03Copyright © 2003 Delta Mach

Strany 2 - GENERAL SAFETY RULES

103. Loosen tracking lock knob (D) Fig. 14, and whilerotating the belt (F) by hand, as shown, tighten or loosentracking knob (E) until the belt is run

Strany 3

11ADJUSTING POSITION OFSANDING ARMDISCONNECT MACHINE FROM POWERSOURCE.The sanding arm can be positioned in the vertical orhorizontal position, or at a

Strany 4 - ADDITIONAL SAFETY RULES

12ADJUSTING TABLE SQUAREWITH SANDING DISCDISCONNECT MACHINE FROM POWERSOURCE.1. Place an accurate square (C) Fig. 23, on the table withone end of the

Strany 5 - MOTOR SPECIFICATIONS

13ADJUSTING THE PLATENThe platen (A) Fig. 24, is set at the factory 1/32 of an inchhigher than the crown of the drums (B). This allows thebelt, when p

Strany 7 - FUNCTIONAL DESCRIPTION

15PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

Strany 8 - INSTALLING ABRASIVE DISC

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

Strany 9

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Strany 10 - BELT SANDER TABLE

31. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations, and specific hazard

Strany 11 - DISC SANDER TABLE

4FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SAFETY RULESFOR ABRASIVE FINISHING MACHINES SAVE THESE INSTRUCTIONS. R

Strany 12 - ADJUSTING MITER GAGE

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Strany 13 - ADJUSTING THE PLATEN

6Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug

Strany 14

7FOREWORDDelta Model 31-731 is a abrasive finishing machine. The Delta Model 31-731 includes two tilting tables, 4½" arbor pulley,V-belt, 80-grit

Strany 15 - ACCESSORIES

8ALIGNING PULLEYS,ASSEMBLING BELT ANDADJUSTING BELT TENSIONDISCONNECT MACHINE FROM POWERSOURCEUsing a straight edge (A) Fig. 6, make certain the motor

Strany 16 - • DELTA)

9OPERATING CONTROLS AND ADJUSTMENTSSTARTING AND STOPPINGTHE ABRASIVE FINISHINGMACHINETo start the machine, push “ON” button (A) Fig. 10. Tostop the ma

Komentáře k této Příručce

Žádné komentáře